Author Topic: gentoo ebuild for 0.3.017 (Read 8337 times)

loux · « **Reply #30 on:** November 21, 2006, 01:06:49 pm »

great Leon,
ok so psclient works !
to resolve your error when logging in with ebuild psclient you need to copy data and art from official client folder,
the data and art from source are not up to date
hope to see you soon on ps
loux

Leon · « **Reply #31 on:** November 21, 2006, 01:24:45 pm »

yes it works fine.. just if you want it to look pretty you will have to change from the cvs skin in ./pssetup

Good work Ioux..

loux · « **Reply #32 on:** November 21, 2006, 01:29:45 pm »

thanks
i have to put CEL=/opt/crystal/lib/cel to ebuilds
loux

Leon · « **Reply #33 on:** November 21, 2006, 01:51:50 pm »

Quote from: loux on November 21, 2006, 01:29:45 pm

thanks
i have to put CEL=/opt/crystal/lib/cel to ebuilds
loux

hmm.. If i close the console it forgets and i have to set CEL=/opt/crystal/lib/cel everytime i load the console.. is it suppose to remember?

Edit.. tried to explain myself better

loux · « **Reply #34 on:** November 21, 2006, 02:00:39 pm »

Hello Leon,
no it's not suppose to be write each time
just put in /etc/env.d/90crystalspace the line CEL=/opt/crystal/lib/cel
and then "etc-update && env-update && source /etc/profile"
and next reboot it will be done for every users

loux

Leon · « **Reply #35 on:** November 21, 2006, 02:06:45 pm »

ok thank you.. all done

KTA · « **Reply #36 on:** November 21, 2006, 03:02:59 pm »

Err... is there a way to extract the needed files from the bin installer? I do not want to install it and clutter my filesystem...

KTA

loux · « **Reply #37 on:** November 21, 2006, 03:17:34 pm »

hello KTA, i don't if there a way to extract it, but when you lauch it,
it ask you for a folder to install it so it's safe to execute it

loux

KTA · « **Reply #38 on:** November 21, 2006, 03:20:40 pm »

Ok, I'll give it a try, I just hope it does not screw with any config files... $:-\$

KTA

Leon · « **Reply #39 on:** November 21, 2006, 03:40:25 pm »

what i did was install it into /tmp/ps then uninstalled it after I got the files i needed, it does not leave that directory so you should be safe

KTA · « **Reply #40 on:** November 21, 2006, 04:04:36 pm »

$\\o//$ It works like a charm now... Thank you very much loux!

KTA

loux · « **Reply #41 on:** November 21, 2006, 04:16:37 pm »

you're welcome
loux

semson · « **Reply #42 on:** November 22, 2006, 04:10:30 am »

ok i just tried the .17 ebuild. the emerge goes pretty straight forward, no error.
i am currently at work, so can't test the build at the moment -- actually i get it done through ssh

one thing to point out, the below messages pop after finished compilling:
* Configure your client by running 'planeshift-setup'
i think it should be :
#/opt/planeshift/bin/pssetup

and it is in /opt folder so we can't:
* Type 'planeshift' to start the Planeshift client

but #/opt/planeshift/bin/psclient

correct me if i am wrong

Leon · « **Reply #43 on:** November 22, 2006, 05:20:21 am »

I dont think those commands work you have to be in the dir then type "./psclient" to run it and "./pssetup" to set it up prior to playing

running this command "/opt/planeshift/bin/psclient" it tries to load but exits with this error

Code: [Select]

 ERROR: csInitializer::SetupConfigManager failed! Is your CRYSTAL environment variable set?

but loads straight away if i go to "/opt/planeshift/bin" then type "/opt/planeshift/bin/psclient"

I have been pulling all nighters so i cant really think

but im sure there is a simpy way around this

loux · « **Reply #44 on:** November 28, 2006, 06:45:15 pm »

so they are just 3 or 4 people using gentoo,
too bad

loux